Feeder Shared Parameters

The shared parameters added to distribution equipment related to the feeder to the distribution equipment.

Numeric Parameters

Parameter types in this section are set to number unless otherwise noted.

DMEN_Feeder_ConductorWireArea: The area of the conductor wire as an area parameter. The area is for a single conductor wire. It does not account for parallel runs or the number of poles.

DMEN_Feeder_ConduitArea: The area of the conduit as an area parameter.

DMEN_Feeder_FrameSize: The frame size of the upstream OCP for the distribution equipment as a current parameter.

DMEN_Feeder_GroundWireArea: The area of the ground wire as an area parameter.

DMEN_Feeder_Length: The length of the feeder as a length parameter.

DMEN_Feeder_NeutralWireArea: The area of the neutral wire as an area parameter.

DMEN_Feeder_NeutralWireCount: The number of neutral wires.

DMEN_Feeder_ParallelRuns: The number of parallel runs.

DMEN_Feeder_RPer1000ft: The resistance per 1000' for the feeder.

DMEN_Feeder_TripSize: The trip size of the upstream OCP for the distribution equipment as a current parameter.

DMEN_Feeder_WireAmpacity: The ampacity of the feeder wire as a current parameter.

DMEN_Feeder_XPer1000ft: The reactance per 1000' for the feeder.

DMEN_Feeder_ZPer1000ft: The impedance per 1000' for the feeder.

DMEN_Feeder2_ConductorWireArea: The area of the conductor wire of the second feeder as an area parameter. The area is for a single conductor wire. It does not account for parallel runs or the number of poles.

DMEN_Feeder2_ConduitArea: The area of the conduit of the second feeder as an area parameter.

DMEN_Feeder2_FrameSize: The frame size of the upstream OCP of the second feeder for the distribution equipment as a current parameter.

DMEN_Feeder2_GroundWireArea: The area of the ground wire of the second feeder as an area parameter.

DMEN_Feeder2_Length: The length of the feeder of the second feeder as a length parameter.

DMEN_Feeder2_NeutralWireArea: The area of the neutral wire of the second feeder as an area parameter.

DMEN_Feeder2_NeutralWireCount: The number of neutral wires of the second feeder .

DMEN_Feeder2_ParallelRuns: The number of parallel runs of the second feeder .

DMEN_Feeder2_RPer1000ft: The resistance per 1000' for the feeder of the second feeder .

DMEN_Feeder2_TripSize: The trip size of the upstream OCP for the distribution equipment of the second feeder as a current parameter.

DMEN_Feeder2_WireAmpacity: The ampacity of the feeder wire of the second feeder as a current parameter.

DMEN_Feeder2_XPer1000ft: The reactance per 1000' for the feeder of the second feeder .

DMEN_Feeder2_ZPer1000ft: The impedance per 1000' for the feeder of the second feeder .

Text Parameters

Parameter types in this section are set to text.

DMET_Feeder_ConductorWireArea: The area of the conductor wire. The area is for a single conductor wire. It does not account for parallel runs or the number of poles. If there are two feeders, both conductor sizes are shown, separated by a slash. The default feeder schedule includes this parameter as a hidden column and sorts the schedule using it.

DMET_Feeder_ConductorWireSize: The number of parallel runs and the size of the conductor wires. Displayed in the default fault current schedule. If there are two feeders, both feeder sizes are shown, separated by a slash.

DMET_Feeder_ConductorWireSizeOnly: The size of the conductor wires. If there are two feeders, both feeder sizes are shown, separated by a slash.

DMET_Feeder_ConduitSize: The size of the conduit. If there are two feeders, both conduit sizes are shown, separated by a slash.

DMET_Feeder_Display: A Yes or No value that indicates whether the feeder should be displayed in the feeder schedule. The default feeder schedule includes this parameter as a hidden column. Any distribution equipment with the value set to No are not included in the schedule. Electrical equipment with their Part Type set to Equipment Switch are automatically set to No so they are not displayed in the schedule.

DMET_Feeder_FeederID: The ID  on the one-line diagram of the first feeder.

DMET_Feeder_FrameSize: The frame size of the upstream OCP of the first feeder for the distribution equipment.

DMET_Feeder_GroundWireSize: The size of the ground wire. If there are two feeders, both ground wire sizes are shown, separated by a slash.

DMET_Feeder_IGConductor: A Yes or No value that indicates whether the first feeder includes an IG conductor.

DMET_Feeder_Length_ft: The length of the feeder in feet. If there are two feeders, both lengths are shown, separated by a slash. Displayed in the default fault current schedule.

DMET_Feeder_Length_m: The length of the feeder in meters. If there are two feeders, both lengths are shown, separated by a slash.

DMET_Feeder_NeutralWireSize: The size of the neutral wire. If there are two feeders, both neutral wire sizes are shown, separated by a slash.

DMET_Feeder_ParallelRuns: The number of parallel runs of the first feeder.

DMET_Feeder_RPer1000ft: The resistance of the feeder per 1000'. If there are two feeders, both resistances are shown, separated by a slash.

DMET_Feeder_TripSize: The trip size of the upstream OCP of the first feeder for the distribution equipment.

DMET_Feeder_Trip_Poles: The trip size and number of poles of the upstream OCP of the first feeder for the distribution equipment. The trip and poles are separated by a slash, for example, 100/3.

DMET_Feeder_WireAmpacity: The ampacity of the feeder wire of the first feeder.

DMET_Feeder_WireCallout: The callout of the first feeder. The callout lists the conduit size and all of the wire sizes.

DMET_Feeder_XPer1000ft: The reactance of the feeder per 1000'. If there are two feeders, both reactances are shown, separated by a slash.

DMET_Feeder_ZPer1000ft: The impedance of the feeder per 1000'. If there are two feeders, both impedances are shown, separated by a slash.

DMET_Feeder1_ConductorWireArea: The area of the conductor wire of the first feeder. The area is for a single conductor wire. It does not account for parallel runs or the number of poles.

DMET_Feeder1_ConductorWireSize: The number of parallel runs and the size of the conductor wires of the first feeder.

DMET_Feeder1_ConductorWireSizeOnly: The size of the conductor wires of the first feeder.

DMET_Feeder1_ConduitSize: The size of the conduit of the first feeder.

DMET_Feeder1_GroundWireSize: The size of the ground wire of the first feeder.

DMET_Feeder1_Length_ft: The length of the feeder in feet of the first feeder.

DMET_Feeder1_Length_m: The length of the feeder in meters of the first feeder.

DMET_Feeder1_NeutralWireSize: The size of the neutral wire of the first feeder.

DMET_Feeder1_RPer1000ft: The resistance of the feeder per 1000' of the first feeder.

DMET_Feeder1_XPer1000ft: The reactance of the feeder per 1000' of the first feeder.

DMET_Feeder1_ZPer1000ft: The impedance of the feeder per 1000' of the first feeder.

DMET_Feeder2_ConductorWireArea: The area of the conductor wire of the second feeder. The area is for a single conductor wire. It does not account for parallel runs or the number of poles.

DMET_Feeder2_ConductorWireSize: The number of parallel runs and the size of the conductor wires of the second feeder.

DMET_Feeder2_ConductorWireSizeOnly: The size of the conductor wires of the second feeder.

DMET_Feeder2_ConduitSize: The size of the conduit of the second feeder.

DMET_Feeder2_Display: A Yes or No value that indicates whether the feeder should be displayed in the feeder schedule. Electrical equipment with their Part Type set to Equipment Switch are automatically set to No so they are not displayed in the schedule.

DMET_Feeder2_FeederID: The ID  on the one-line diagram of the second feeder.

DMET_Feeder2_FrameSize: The frame size of the upstream OCP of the second feeder for the distribution equipment.

DMET_Feeder2_GroundWireSize: The size of the ground wire of the second feeder.

DMET_Feeder2_IGConductor: A Yes or No value that indicates whether the second feeder includes an IG conductor.

DMET_Feeder2_Length_ft: The length of the feeder in feet of the second feeder.

DMET_Feeder2_Length_m: The length of the feeder in meters of the second feeder.

DMET_Feeder2_NeutralWireSize: The size of the neutral wire of the second feeder.

DMET_Feeder2_ParallelRuns: The number of parallel runs of the second feeder.

DMET_Feeder2_RPer1000ft: The resistance of the feeder per 1000' of the second feeder.

DMET_Feeder2_TripSize: The trip size of the upstream OCP of the second feeder for the electrical equipment.

DMET_Feeder2_WireAmpacity: The ampacity of the feeder wire of the second feeder.

DMET_Feeder2_WireCallout: The callout of the second feeder. The callout lists the conduit size and all of the wire sizes.

DMET_Feeder2_XPer1000ft: The reactance of the feeder per 1000' of the second feeder.

DMET_Feeder2_ZPer1000ft: The impedance of the feeder per 1000' of the second feeder.

Yes/No Parameters

Parameter types in this section are set to yes/no.

DMEB_Feeder_NeutralDouble: Whether the neutral wire of the first feeder is set to double the phase wire as a yes/no parameter.

DMEB_Feeder2_NeutralDouble: Whether the neutral wire of the second feeder is set to double the phase wire as a yes/no parameter.


Page url: http://www.designmaster.biz/docs/elecrt/index.html?feeder_shared_parameters.htm
©2013-2017 Design Master Software, Inc