Pipe Types

The Pipe Types commands are used to customize the pipe types used in your project.

See the General Customization Commands section for more information about how the Edit Project List, Edit Standards List, Copy Project List to Standards, and Copy Standards List to Project commands work.

To customize the pipe types in the current project, go to

Ribbon: DMP: Customization->Project Customization-> dm_plumb-pipeTypesP Pipe Types

Pulldown Menu: DM Plumbing->Customization->Pipe Types->Edit Project List

To customize the pipe type standards, go to

Ribbon: DMP: Customization->Standards Customization-> dm_plumb-pipeTypesS Pipe Types

Pulldown Menu: DM Plumbing->Customization->Pipe Types->Edit Standards List

Pipe Type Dialog Box

customization--pipe-type-dialog-box

Move Up: Press this button to move the selected pipe type up in the list.

Move Down: Press this button to move the selected pipe type down in the list.

Delete: Press this button to delete the selected pipe type. The pipe type cannot be deleted if it is currently in use.

New: Press this button to create a new pipe type. The Select Pipe Type dialog box will appear.

customization--select-pipe-type-dialog-box

Select the pipe type to copy settings from and press the OK button. A new pipe type will be created. The layers, labels, linetypes, flow categories, sizes, and sizing tables for the new pipe type will match the settings for the pipe type that was copied.

Name: The full name of the pipe type.

Short Name: The shorthand name of the pipe type. This value is used when generating new layer names for the pipe type.

Flow Direction: Sets the flow direction of the pipe type toward or away from fixtures. This setting only affects the direction of the arrowhead when inserting the pipe on the drawing.

Elbow Graphic: How the pipe type is drawn when two pipes connect at an angle.

Right Angle: No additional graphics will be drawn.
45-degree Angle: A line will be inserted at a 45-degree angle to the connecting pipe segments.
Arc: An arc will be inserted between the connected pipe segments.

Tee Graphic: How the pipe type is drawn when two pipes connect at a tee.

Right Angle: No additional graphics will be drawn.
45-degree Angle: A line will be inserted at a 45-degree angle to the connecting pipe segments.
Arc: An arc will be inserted between the connected pipe segments.

Fitting Ticks: Whether tick marks are displayed on the pipe at pipe symbols. If Show tick marks before pipe symbols is set to No, tick marks will not be shown for pipe symbols. See the Pipe Fittings section for more information.

Label Location: Where pipe labels will be inserted on the pipe.

Above Pipe Line: The label will be inserted above or below the pipe line.
In Pipe Line, Rotated to Match Pipe Angle, Displayed by Default: The label will be inserted inside and parallel to the pipe line. The label will be displayed on new pipes that are inserted.
In Pipe Line, Rotated to 0, Displayed by Default: The label will be inserted inside the pipe line at a rotation angle of 0. The label will be displayed on new pipes that are inserted.
In Pipe Line, Rotated to Match Pipe Angle, Not Displayed by Default: The label will be inserted inside and parallel to the pipe line. The label will not be displayed on new pipes that are inserted.
In Pipe Line, Rotated to 0, Not Displayed by Default: The label will be inserted inside the pipe line at a rotation angle of 0. The label will not be displayed on new pipes that are inserted.

Hide Pipes Below Ductwork: Whether the pipe type will be displayed with hidden lines when it runs underneath ductwork drawn by Design Master HVAC. Hidden pipes will appear as dashed lines when underneath the ductwork.

If this box is checked, settings in the Pipe Linetypes dialog box for the pipe linetype will be disabled. The pipe linetype must be set to CONTINUOUS.

Edit Labels: Press this button to open the Pipe Labels dialog box.

Edit Linetypes: Press this button to open the Pipe Linetypes dialog box.

Edit Flow Categories: Press this button to open the Pipe Flow Categories dialog box.

Edit Sizes: Press this button to open the Pipe Sizes dialog box.

Edit Sizing Tables: Press this button to open the Pipe Sizing Tables dialog box.

Related Options

45-degree turn size & arc radius: Sets how 45-degree angle and arc elbows and tees are displayed.


Page url: http://www.designmaster.biz/docs/plumb/index.html?pipe_types.htm
©2012-2023 Design Master Software, Inc